If you only pick up one candle habit, make it this one: trim the wick to about 1/4 inch before every burn. It takes less than a minute, it costs nothing, and it changes how your candle burns from the first light to the last bit of wax.
What happens when you skip it
A wick that’s too long pulls up more melted wax than the flame can burn cleanly. The flame grows tall, starts to flicker and sends up a thin trail of black smoke. You’ll see the results on the inside of a jar as a dark ring of soot, or on the underside of a tin lid.
A long wick also tends to “mushroom.” Carbon collects on the tip and forms a small ball that makes the flame larger still. Those carbon bits can break off and fall into the wax, leaving dark specks in your candle.
A bigger flame burns hotter and faster, too. The wax gets used up sooner, the container gets hotter than it needs to, and you get fewer hours out of the candle you bought.
How short is short enough?
About 1/4 inch, or roughly 6 millimeters. That’s short enough to keep the flame calm and steady, but long enough to light easily and stay lit. Trim it every time, including before the very first burn, since a wick can be left a little long when a candle is made.
Always trim with the candle out and the wax hardened. Trimming into soft or liquid wax pushes debris into the pool and makes it hard to see what you’re doing.
Tools that work
- A wick trimmer. These look like scissors with an angled head and a small flat tray that catches the trimmed piece. The angle lets you reach into a deep jar without tipping it.
- Nail clippers. Surprisingly handy for tins and shallow containers. Keep a pair just for candles.
- Small scissors. Fine for wide, shallow candles, though they can be hard to get down into a jar once it’s half burned.
Whatever you use, keep a paper towel nearby to catch the trimmings.
The 30-second routine
- Check that the candle is cool. The wax should be solid, not soft.
- Pick out any debris. Remove old wick trimmings, match ends or dust from the surface.
- Snip the wick to 1/4 inch. If the tip has mushroomed, the trim takes the carbon ball off with it.
- Catch the trimming. Don’t let it fall back into the wax, where it can act like a second little wick.
- Center the wick. If it’s leaning, straighten it gently so the flame sits in the middle of the container.
That’s it. Light it and enjoy.
A note about our wicks
All of our candles use coreless cotton flat braid wicks with paper filaments, which give the wick extra rigidity and strength. You might notice that a flat braid wick curls slightly as it burns. That’s by design: the tip bends into the hottest part of the flame and burns away a little as you go. It helps, but it doesn’t replace trimming. When a candle cools, the charred tip stays behind, and a quick trim before you relight gives you a fresh, even start. You’ll find more about what goes into our candles on our FAQ page.
Common trimming mistakes
Cutting it too short
It’s possible to overdo it. A wick trimmed down to almost nothing gives a weak, tiny flame that can’t melt enough wax, and it may drown in the melt pool and go out. If that happens, put the candle out, let it harden, and carefully remove a little wax from around the wick with a spoon so more of it is exposed. Next time, aim for that 1/4 inch rather than as short as possible.
Trimming while the wax is still liquid
It’s tempting to trim right after you put a candle out, while you’re thinking of it, but the trimmed piece almost always lands in the pool and the wick bends in the soft wax. Wait until the surface has set.
Trimming only when it looks bad
By the time a wick is visibly mushroomed and smoking, the soot is already on the glass. Trimming every time, even when the wick looks fine, is what keeps that from happening at all.
What if the flame gets too big mid-burn?
Sometimes a candle that started out calm begins to flicker or smoke after a few hours. Don’t try to trim a lit wick. Put the candle out, let the wax set, trim the wick, and relight it. To put the flame out cleanly, use a snuffer, or gently dip the wick into the melted wax with a wick dipper and straighten it back up. Blowing a candle out can spatter wax and send up a puff of smoke.
Habits that go with it
Trimming works best alongside a few other simple habits:
- Let the first burn last long enough for the melted wax to reach the edges. If it doesn’t, the candle can start to tunnel; here’s how to prevent and fix tunneling.
- Burn for no more than about four hours at a time.
- Keep candles out of drafts.
- Stop when about 1/2 inch of wax is left in the bottom of the container.
Keep a wick trimmer next to your matches and the habit takes care of itself. A neat wick, a steady flame and a clean container are the easiest way to get every hour out of a candle, whether it’s a small tin on your nightstand or a big jar on the coffee table. And if you’ve wondered how the wax itself affects soot, we compared the two most common candle waxes in soy wax vs paraffin.
