You light a candle, enjoy it for an evening, and a few burns later there’s a narrow hole down the middle with a thick wall of untouched wax all around it. That’s tunneling. It wastes a good part of the candle, it weakens the scent, and if it gets deep enough, the wick can drown in its own pool of wax. The good news is that it’s almost always preventable, and often fixable.
What tunneling looks like
A candle that is burning well forms a full melt pool, a layer of liquid wax that reaches all the way to the sides of the container. As it burns down, the surface stays fairly flat and the sides of the jar or tin come out mostly clean. A tunneling candle melts only a small circle around the wick. Each burn digs that circle a little deeper, and the ring of hard wax around it gets taller.
Why it happens
The first burn was too short
This is the big one. Wax has a “memory.” Whatever size melt pool forms the first time you light a candle tends to be the size it returns to on every burn after that. If you light a new candle for twenty minutes before leaving the house, you may have set its course for the rest of its life. Soy wax in particular holds on to that memory, which is why the first burn matters so much with natural soy candles.
Every burn after that was short, too
Even a candle that started well can begin to tunnel if it’s only ever lit for short stretches. The melt pool never has time to reach the edges, so the center keeps sinking.
Drafts and uneven surfaces
A breeze from a vent or a fan pushes the flame to one side, and the wax melts unevenly. A candle sitting on a tilted shelf does the same thing. You’ll often see a one-sided tunnel, with one wall of the container clean and the opposite side thick with wax.
A wick that wandered off center
If the wick leans or drifts, the heat leans with it. Gently straightening the wick right after you put the candle out, while the wax is still soft, keeps it centered for the next burn.
The wick is too small for the container
Sometimes the problem is in how a candle was made. A wick that’s too small for the container’s diameter can’t produce enough heat to melt wax all the way across, no matter how long you burn it. That’s something makers have to test when they pair wicks with containers, and it isn’t something you can fix at home.
How to prevent it: the first burn
A good rule of thumb is to let the first burn last about one hour for every inch of the container’s diameter. A candle about three inches across needs roughly three hours. The goal isn’t really the clock, though. It’s the melt pool: keep the candle lit until the liquid wax reaches the edges of the container all the way around.
Wider containers, like our apothecary jars, need more time on that first burn than smaller tins. Before lighting a new candle, check that you’ll actually be home and awake for the next few hours. If not, save it for another day.
After that first burn, try to give each session enough time for the pool to reach the edges again, but don’t go past about four hours at a time. Very long burns let the wick mushroom and make the container hotter than it should be.
How to fix a candle that’s already tunneling
The foil collar
This is the most reliable fix for a shallow or moderate tunnel.
- Trim the wick to about 1/4 inch.
- Wrap a piece of aluminum foil around the top of the container so it covers the outer ring of wax, leaving an opening an inch or so wide in the center above the wick.
- Light the candle. The foil reflects heat back onto the hard wax around the edges and helps it melt down.
- Check on it often. Once the surface is level and the melt pool reaches the sides, the candle is reset. This usually takes an hour or two.
- Remove the foil carefully with an oven mitt, since it will be hot, and either let the candle keep burning or put it out.
Never leave a candle with a foil collar unattended, and keep it on a heat-safe surface the whole time.
Even out the surface with gentle heat
For a candle that has only just started to tunnel, you can warm the top layer of the unlit candle with a hair dryer on a low setting until the surface softens and levels out. Let it set, trim the wick, and then give it a long burn so the melt pool reaches the edges.
If the wick is drowning
Deep tunnels sometimes collect so much liquid wax around a short wick that the flame shrinks or goes out. Put the candle out, let it harden, and use a spoon or butter knife to carefully remove a little wax from around the wick so more of it is exposed. Don’t pour liquid wax down a drain, since it hardens in the pipes.
Small habits that keep it from coming back
- Trim the wick before every burn. A neat 1/4 inch wick gives a steady, centered flame; see our guide to trimming the wick.
- Keep candles away from vents, fans and windows.
- Set candles on a flat, level, heat-safe surface.
- Plan longer burns rather than many short ones.
- Straighten the wick gently after putting the candle out, while the wax is still soft.
We use coreless cotton flat braid wicks with paper filaments, which stay sturdy as the wax melts around them. You’ll find more about our wicks and wax in our FAQ, and if you’re curious why we pour with soy in the first place, read soy wax vs paraffin: what burns cleaner?
A tunnel isn’t the end of a candle. With a little foil, a little patience and a proper first burn on the next one, you’ll get every bit of fragrance out of the wax you paid for.
